吹&吹法：在I.S行列机上制作小口瓶制造瓶的原理。我们常使用的方法。玻璃先在初模中吹制，然后在成模再吹制成玻璃瓶。
BLOW & BLOW：
expression used to identify the production principleof the I.S machine making narrow neck containers. glass is brown in the blankmold and later brown again in the blow mold.
吹&吹法的模具设备 Blow &Blow Process Mold Equipment
1.漏斗 Funnel
此工艺漏斗有二个作用。一是将料滴引入初模里，二是提供一个空间使得“扑气”的压缩空气进入初模。
The funnel has two functions. First it acts as a guide for the gob to enterthe blank. Second it provides clearancefor the introduction of “settle blow” air into the blank.
The funnel has two functions. First it acts as a guide for the gob to enterthe blank. Second it provides clearancefor the introduction of “settle blow” air into the blank.
2.闷头 Baffle
此工艺闷头也有二个作用。一是将扑气”的压缩空气通过闷头内的通孔提供一个路径，二是它在初模的上方与初模组成完整的初模腔，以形成初模料坯状。
The baffle has two functions. First it provides settle blow air throughinternal porting in the baffle. Secondit seats on top of the blank completing the blank cavity for the formation of theparison.
The baffle has two functions. First it provides settle blow air throughinternal porting in the baffle. Secondit seats on top of the blank completing the blank cavity for the formation of theparison.
3.初模 Blank
它是形成初坯的部件，通过扑气和倒气形成初模料坯。经过设计的初模形状，玻璃瓶可以做出合适的瓶壁厚度。
The blank is the primary piece usedto form the parison through the use of settle blow air and counter blowair. It is designed to provide thecorrect amount of glass wall thickness throughout the finished container.
The blank is the primary piece usedto form the parison through the use of settle blow air and counter blowair. It is designed to provide thecorrect amount of glass wall thickness throughout the finished container.
4.口模 Neckring
口模它是由二瓣口模与一个口环组成。口环装在口模内，瓶口顶部的密封面是由此口环形成的，整个瓶口是由此口模形成的。同时口模它夹撑着初料坯从初模侧翻转到成模里。口环有时我们也称为口板。
The neckring consists of twoneckring halves and a guide ring. Theguide ring is an internal part and normally forms the top of sealing surface ofthe finish. The neckring forms thefinish and holds the parison during transfer from the blank to the mold. The guide ring is sometimes referred to as aguide plate.
The neckring consists of twoneckring halves and a guide ring. Theguide ring is an internal part and normally forms the top of sealing surface ofthe finish. The neckring forms thefinish and holds the parison during transfer from the blank to the mold. The guide ring is sometimes referred to as aguide plate.
5.套筒 Thimble
套筒护导者芯子进入口模里，同时在倒气时起着密封的作用。
The thimble guides the plunger intothe neckring and creates a seal for counter blow air.
The thimble guides the plunger intothe neckring and creates a seal for counter blow air.
6.芯子 Plunger
在形成瓶口时，芯子插入其内部形成一空穴，倒气时通过此路径进入玻璃液内，从而形成初模料坯。
The plunger forms the inside surfaceof the finish and provides counter blow during the parison forming process.
The plunger forms the inside surfaceof the finish and provides counter blow during the parison forming process.
7.成模 Mold
成模是形成玻璃瓶最终形状的。
The mold forms the finished container.
The mold forms the finished container.
8.模底 Bottom Plate
模底与成模配合形成玻璃瓶的，模底是成形于瓶底的。
The bottom plate is used inconjunction with the mold to form the finished container. The bottom plate forms the bottom of thecontainer.
The bottom plate is used inconjunction with the mold to form the finished container. The bottom plate forms the bottom of thecontainer.
9.吹气头 Blowhead
吹气头工作在成模上方，正吹气通过它吹涨初模料坯，使其成形。
